Paver base: how deep to dig and how much gravel you need

Pavers get the attention, but the base does the work. A patio that sinks, rocks or grows weeds in the joints almost always has a base that was too thin, poorly compacted or made of the wrong material. This guide covers how deep each layer should be and how to work out your excavation depth before you dig.

Short answer

  • Patios and walkways: about 6–10 in (15–25 cm) of compacted gravel base, deeper on clay.
  • Driveways: about 8–14 in (20–35 cm) of compacted base.
  • Bedding layer: about 1 in (25 mm) of coarse sand or fine clean chip, screeded, not compacted before laying.
  • Excavation: base + bedding + paver thickness, measured from the finished surface.

Ranges reflect published guidance from paver manufacturers. Always follow the installation guide for the pavers you buy.

Cross-section of a paver patio Layers from top: pavers with sand-filled joints, a thin bedding layer, a thick compacted gravel base, geotextile fabric, and compacted soil. An edge restraint holds the pavers at the side. edge restraint ↘ Pavers, often 2⅜–3⅛ in Gravel base, 6–10 in (patio) Compacted subgrade Bedding sand ≈ 1 in
Typical paver patio layers. The base carries the load; the bedding layer only levels the pavers.

Layer by layer

Subgrade

The native soil under everything. Remove sod, roots and dark organic topsoil until you reach firm subsoil, then compact it. Soft spots should be dug out and replaced with base material. On clay or wet soils, a geotextile fabric between soil and base keeps the two from mixing.

Gravel base

Crushed stone, placed in thin lifts and compacted. The usual choice is a dense-graded crushed aggregate with fines (often sold as ¾ minus, road base or crusher run), which compacts very tightly. Permeable paver systems instead use clean crushed stone without fines so water drains through. Never use pea gravel or rounded stone; it will not lock together.

Compact in lifts of about 2–4 in, with a plate compactor, rather than spreading the full depth and compacting once. A plate compactor cannot firm up a thick layer all the way down.

Bedding layer

A thin, even layer of coarse, washed concrete sand or a small clean chip (for example ⅛ in chip). It lets you set each paver at exactly the right height. About 1 in is standard. A thicker bedding layer is a common mistake: it moves and settles unevenly, so dips and lumps appear later. Fix low spots in the base, not with extra sand.

Pavers and joint sand

Once laid, the pavers are compacted into the bedding layer and the joints are filled with sand (regular or polymeric). The filled joints transfer load between pavers, which is what makes a segmental surface work.

Edge restraint

Plastic, metal or concrete edging along every edge that is not against a wall. Without it, the outer pavers creep outward and the joints open up.

How soil changes the base depth

Typical compacted base depth by soil type
SubsoilPatio or walkwayDriveway
Sandy, well-drainedAbout 6 inAbout 8 in
SiltyAbout 8 inAbout 12 in
ClayAbout 10 inAbout 14 in

Source: ranges published by paver manufacturer Unilock (see sources). Cold climates with deep frost and sites with poor drainage often need more.

Working out your excavation depth

Add the layers from the finished surface down:

excavation = paver thickness + bedding (≈1 in) + base depth

Examples with a 2⅜ in (60 mm) paver
ProjectBaseTotal dig below finished height
Patio on sandy soil6 in≈ 9⅜ in
Patio on clay10 in≈ 13⅜ in
Driveway on silty soil (3⅛ in paver)12 in≈ 16⅛ in

Measure from where the finished surface will be, not from the current ground. If the patio is meant to sit higher than the lawn, you dig less.

Slope: plan it into the base

A patio needs a gentle slope so water runs away from the house. A fall of about ⅛–¼ in per foot (roughly 1–2%) is commonly used. Build the slope into the compacted base so the bedding layer stays an even 1 in. A string line between stakes, set to the planned fall, makes this easy to check.

Base volume example

A 12 × 16 ft patio (192 ft²) on silty soil with an 8 in base:

  • Base volume: 192 × 8 ÷ 12 = 128 ft³ = 4.74 yd³ compacted. With a 15% compaction allowance, order about 5.5 yd³.
  • Bedding sand: 192 × 1 ÷ 12 = 16 ft³ ≈ 0.6 yd³.

Most base materials extend 6–12 in beyond the paver edge so the edge restraint sits on solid ground. Add that strip to your area.

Common mistakes

  1. Leaving topsoil in place under the base.
  2. Compacting the full base in one pass.
  3. Using thick sand to make up for an uneven base.
  4. Stopping the base at the paver edge, so the edges sink.
  5. Forgetting the slope until the pavers are down.

Frequently asked questions

Can I lay pavers on sand only?

Not for a lasting patio. Sand alone does not carry load or drain like a crushed base; the surface will settle and shift.

Should I compact the bedding sand?

No. Screed it flat and leave it loose. The pavers are compacted into it after they are laid.

Do I need fabric under the base?

It is recommended on clay and wet soils, and often specified for driveways. On firm sandy soil it is optional.

The patio paver planner calculates pavers, gravel base, bedding sand, edging and joint sand for several areas at once.

Sources and further reading

The ranges in this guide summarize published guidance like the sources above. Always follow the instructions for your specific product and any local rules.

Related