Running out of concrete with three posts left is a common fencing story. The fix is simple arithmetic: the volume of the hole, minus the post, divided by what one bag yields. This guide shows the math, gives charts for common post sizes, and explains how to count posts.
The formula
- Hole volume (cylinder) = 3.1416 × (diameter ÷ 2)² × concrete depth
- Post volume (square post) = width × width × concrete depth. For round posts, use the cylinder formula with the post diameter.
- Concrete per hole = hole volume − post volume
- Convert cubic inches to cubic feet by dividing by 1,728.
- Bags = cubic feet ÷ bag yield, rounded up
Use the depth of concrete, not the full hole. If you put 4 in of gravel in a 28 in hole, the concrete is 24 in deep.
Typical bag yields
The yield is printed on the bag and is the number to trust. Common figures for standard concrete mixes are:
| Bag weight | Approximate yield |
|---|---|
| 40 lb | 0.30 ft³ |
| 50 lb | 0.375 ft³ |
| 60 lb | 0.45 ft³ |
| 80 lb | 0.60 ft³ |
Fast-setting post mixes, which are poured dry into the hole and then watered, often have a different yield. Use the label.
Bags per post: ready-made charts
Figures below are per hole, rounded up, and assume the yields above.
| Post | Hole diameter | Concrete depth | Concrete | 50 lb bags | 80 lb bags |
|---|---|---|---|---|---|
| 4×4 (3½ in) | 8 in | 24 in | 0.53 ft³ | 2 | 1 |
| 4×4 (3½ in) | 10 in | 24 in | 0.92 ft³ | 3 | 2 |
| 4×4 (3½ in) | 12 in | 30 in | 1.75 ft³ | 5 | 3 |
| 4×4 (3½ in) | 12 in | 36 in | 2.10 ft³ | 6 | 4 |
| 6×6 (5½ in) | 18 in | 36 in | 4.67 ft³ | 13 | 8 |
| Round 2⅜ in | 10 in | 24 in | 1.03 ft³ | 3 | 2 |
| Round 2⅜ in | 12 in | 30 in | 1.89 ft³ | 6 | 4 |
Real holes are rarely perfect cylinders. Augered holes in clay are close to the nominal size; hand-dug holes in loose or rocky soil can be much wider. Adding about 10% is sensible.
How many posts?
Line posts are usually spaced 6–8 ft apart, set by the panel length or the fence design. For one straight run:
posts = (run length ÷ spacing, rounded up) + 1
Each additional run that shares a corner post adds sections but not an extra corner. Gates usually need their own posts on each side, often larger and deeper.
Worked example
A 100 ft straight fence with posts every 8 ft, 4×4 posts in 10 in holes, 24 in of concrete:
- Sections: 100 ÷ 8 = 12.5, round up to 13
- Posts: 13 + 1 = 14
- Concrete: 14 × 0.92 ft³ = 12.9 ft³
- 80 lb bags: 12.9 ÷ 0.60 = 21.5, so 22 bags if you mix in batches
- If you pour dry mix bag by bag, one hole at a time, count per hole instead: 2 bags × 14 = 28 bags
The difference matters. When each hole gets whole bags, you round up at every hole. When you mix in a wheelbarrow, leftovers go into the next hole.
Tips for pouring
- Set the post on tamped gravel, brace it plumb in two directions, then add concrete.
- Finish the concrete slightly above ground and slope it away from the post so water runs off.
- Wait the time on the bag before hanging panels or gates; full strength takes longer.
- Wear gloves and eye protection; wet concrete is caustic to skin.
Frequently asked questions
Is one 50 lb bag enough for a 4×4 post?
Usually not. Even a small 8 in hole with 24 in of concrete needs about 0.53 ft³, which is more than one 50 lb bag yields.
Can I use less concrete with a narrower hole?
You can, but a thin collar of concrete is weaker and more likely to crack. A hole about three times the post width is the usual guide; see how deep to set fence posts.
The fence post concrete calculator counts posts, concrete bags and optional bottom gravel for your exact fence runs.
Sources and further reading
The ranges in this guide summarize published guidance like the sources above. Always follow the instructions for your specific product and any local rules.