Cubic yards vs. tons: how to order gravel

You measured your driveway in feet, the supplier sells by the ton, and the store sells bags labeled in cubic feet. Converting between them is simple once you know which number to ask for. This guide walks through the math and shows how much one cubic yard actually covers.

The units you will see

  • Cubic yard (yd³): a cube 3 ft on each side, or 27 cubic feet. Most US bulk landscape suppliers sell by the yard.
  • US ton: 2,000 lb (about 907 kg). Quarries and many stone yards sell by weight.
  • Cubic meter (m³) and metric tonne: used outside the US. 1 m³ ≈ 1.31 yd³, and 1 tonne = 1,000 kg ≈ 1.10 US tons.
  • Bags: labeled by volume (for example 0.5 ft³ or 20 L) or by weight (for example 50 lb). The label is what counts.

Step 1: work out the volume

Volume = area × depth. Use the same unit for everything.

  1. Area in square feet = length × width (split odd shapes into rectangles, triangles and circles; see how to measure irregular areas).
  2. Convert the depth to feet: inches ÷ 12. Four inches is 0.333 ft.
  3. Cubic feet = area × depth in feet.
  4. Cubic yards = cubic feet ÷ 27.

Example: a 60 × 10 ft path at 4 in deep is 600 × 0.333 = 200 ft³, which is 200 ÷ 27 = 7.4 yd³ compacted.

Step 2: add allowances

Loose gravel compacts. If you order exactly the compacted volume, you will run short. Add a compaction allowance (10–20% is common for crushed stone) and a small waste allowance for spillage and uneven ground. With 15% + 5%, the 7.4 yd³ path above becomes about 8.9 yd³.

Step 3: convert to tons if needed

Tons = cubic yards × density in tons per cubic yard. Density depends on the rock, its size and its moisture, so ask your supplier for their figure. As a rough starting point, many crushed stones fall between 1.3 and 1.5 tons per cubic yard.

8.9 yd³ at different densities
DensityWeight
1.3 tons/yd³11.6 tons
1.4 tons/yd³12.5 tons
1.5 tons/yd³13.4 tons

The spread is almost two tons on a small job. That is why the density your supplier uses matters more than any rule of thumb.

How much does one cubic yard cover?

One cubic yard is 324 square feet at 1 in deep. Divide by the depth in inches:

Coverage of 1 cubic yard
DepthCoverageTypical use
2 in162 ft²Top-up of an existing surface
3 in108 ft²Garden path surface
4 in81 ft²Single-layer path, driveway top layer
6 in54 ft²Driveway base layer, paver base
8 in40.5 ft²Deeper paver base
12 in27 ft²Full driveway build

These are compacted coverages. Order more to allow for compaction.

Bags or bulk?

Bagged gravel is convenient for small jobs and places a truck cannot reach. It gets expensive and heavy quickly. A common 0.5 ft³ bag holds 1/54 of a cubic yard, so one cubic yard is 54 bags. A single driveway layer can easily be several hundred bags.

A rough rule: once a job passes about one cubic yard, compare a bulk delivery with bags. Include the delivery fee in the comparison. The planner lets you type both prices and shows the cost side by side.

Delivery loads

Trucks are limited by weight. Divide the total weight by the truck's capacity and round up. A 14-ton order on a 10-ton truck is two loads, which often means two delivery fees. If you are building several layers of different stone, each material is usually delivered separately.

Before you order, check:

  • Can a loaded truck reach the drop point without damaging the lawn, curbs or septic system?
  • Where will the pile go, and can you spread it before rain?
  • Is there a minimum order or a short-load fee?

Questions to ask your supplier

  1. Do you sell by the yard or by the ton?
  2. What density do you use for this material?
  3. What size range is it, and does it contain fines?
  4. How many tons does your truck carry, and what is the delivery fee?
  5. Do you recommend a compaction allowance for this stone?

Frequently asked questions

How many tons is a yard of gravel?

Usually somewhere around 1.3 to 1.5 US tons for crushed stone, but it varies. Use your supplier's figure.

How many bags of gravel equal a ton?

Divide 2,000 lb by the bag weight. With 50 lb bags, that is 40 bags per ton. If the bag is labeled by volume, convert using the density instead.

The gravel driveway calculator does all three steps at once, for several sections and two layers, and shows yards, tons, bags and delivery loads in one list.

Related